Exactly How to Remove and Change a Bathtub.
Exactly How to Remove and Change a Bathtub.
Blog Article
Nearly everybody is bound to have their unique assumption on the subject of How to Install a Bathtub.
Mounting a bathtub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job and are comfortable trying it. Rather than working with a professional to take over a halfway-completed task, it is better to think about employing one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your washroom if you have currently acquired a new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as product checklist ought to make up the following:
Preparing for the Setup
Firstly, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly bothersome because of the restricted access that is often the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints and also new pipework for leaks and also tighten them if necessary. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the tub has actually been used a minimum of when as this will settle it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap ports. The previous kind must be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to issues with wetness as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break fairly very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that editorial on Tools You Need to Install a New Bathtub from a friend on a different web blog. Are you aware of another person who is excited by How to Install a Bathtub Yourself? Be sure share it. We recognize the value of reading our article about How to Install a Bathtub.
Get Estimate Report this page